Installing marble tiles on your floor adds beauty and elegance to your home. With the myriad colors to choose from, marble flooring Naples FL can blend in with any color scheme of your room. It is because these stones emit a classic and aesthetic catch that no other stone can. It takes a great deal of work to install tiles but you can do it yourself if you are careful and patient.
Before doing anything, ensure that you protect yourself by adorning the right gear. Make sure that your eyes, face and hands are well protected. If the floor contains tiles already ensure that you take them out using a hammer. In case the flooring is made of Vinyl, you can easily remove them by ripping them with a bar.
Ensure that the floor is clean by scrubbing it thoroughly. After that, level it up using a long level. This is important because uneven floor will cause the marble stones to crack. Some flooring contractors in Naples FL use ply wood for the same purpose. Scrutinize the tiles so that you isolate the ones with defects.
Record the accurate measurements of ground so that you may have the ideal layout on paper. Using the dimensions of marble stones and the length of the surface sides, you can easily plan on how to install them. Draw horizontal and vertical lines with accuracy and as per your preferred pattern so that you are able to see where the tiles will be placed.
Place the tiles on grid. This dry run will help you to assess the floor so that you may make the necessary changes to the pattern or where you will start laying them based on the pattern and the dimensions of the area. You are then supposed to apply a thin adhesive on the floor using a notched trowel. The adhesive should be thick enough that it does not show the ground below.
Place a tile within ten minutes on applying the sticker. Do this carefully without running the marble stone on the adhesive as this will make it to rise above the surface of the tile causing its surface to be rough. This renders the marble stone susceptible to breakage. As if that is not enough, you will consume a lot of time trying to remove the dried sticking film.
After placing the tiles, place the spacers on the corner edges. The spacers keep the layout neat by maintaining straight lines between them so you have straight horizontal and vertical running marble stones. To avoid a rough surface, place a flat wood on top of those you have seen to be raised and tap them lightly so that you push them further downwards.
The last thing in your installation procedure should be to remove the excess adhesive that may have spilt out of the spacing lines. You will notice you have the excess adhesive where you had pushed a stone down using a lot of force. After that, leave the surface to dry for forty eight hours without disturbance so as to have a good finish.
Before doing anything, ensure that you protect yourself by adorning the right gear. Make sure that your eyes, face and hands are well protected. If the floor contains tiles already ensure that you take them out using a hammer. In case the flooring is made of Vinyl, you can easily remove them by ripping them with a bar.
Ensure that the floor is clean by scrubbing it thoroughly. After that, level it up using a long level. This is important because uneven floor will cause the marble stones to crack. Some flooring contractors in Naples FL use ply wood for the same purpose. Scrutinize the tiles so that you isolate the ones with defects.
Record the accurate measurements of ground so that you may have the ideal layout on paper. Using the dimensions of marble stones and the length of the surface sides, you can easily plan on how to install them. Draw horizontal and vertical lines with accuracy and as per your preferred pattern so that you are able to see where the tiles will be placed.
Place the tiles on grid. This dry run will help you to assess the floor so that you may make the necessary changes to the pattern or where you will start laying them based on the pattern and the dimensions of the area. You are then supposed to apply a thin adhesive on the floor using a notched trowel. The adhesive should be thick enough that it does not show the ground below.
Place a tile within ten minutes on applying the sticker. Do this carefully without running the marble stone on the adhesive as this will make it to rise above the surface of the tile causing its surface to be rough. This renders the marble stone susceptible to breakage. As if that is not enough, you will consume a lot of time trying to remove the dried sticking film.
After placing the tiles, place the spacers on the corner edges. The spacers keep the layout neat by maintaining straight lines between them so you have straight horizontal and vertical running marble stones. To avoid a rough surface, place a flat wood on top of those you have seen to be raised and tap them lightly so that you push them further downwards.
The last thing in your installation procedure should be to remove the excess adhesive that may have spilt out of the spacing lines. You will notice you have the excess adhesive where you had pushed a stone down using a lot of force. After that, leave the surface to dry for forty eight hours without disturbance so as to have a good finish.
About the Author:
We can find you the best quality marble flooring Naples FL area when you refer to this website now. To get a better idea of what we offer, visit our related homepage on http://www.jdsfloorconcepts.com.
No comments:
Post a Comment